How To Install Rear Quarter Glass Window

Remove the front track or place it at the rear of the quarter panel.

How to install rear quarter glass window. Install the C-pillar trim panels. You can see the back side of the nut and bolt it is on from the panels that flip up. Step 2 Remove the interior quarter panel trim. Use a caulk gun to apply a thin line of urethane sealant around the inside edge of the window opening.

Line up the edges of the window with the edges of the frame. The upper edge is protected by a separate channel. Remove nut at top rear corner of side panel. Remove the window by sliding the track off the rollers on the glass and the channel on the bottom of the glass off the regulator roller.

Check the rear quarter window glass installation for air or water leaks through the urethane seal. Install new glass panel and tighten the retaining nuts Re-install rear quarter glass panel trim Quarter glass can be easily removed by one person without breaking when glass is held in place by weatherstripping. For additional information refer to Section 501-05. It actually cost more for this window than the.

First drop the top pull up on seat bottom and remove it remove center panel remove 3 allen bolts at bottom on seat back and remove. Headrests they just pull off raise top just enough to make hinged panels flip up. How to glue in a new quarter glass into the right rear of a 2006 Honda Civic. C Install the seal to the glass.

Open the rear door and remove the screws from the interior door paneling trim using the Phillips screwdriver. The rear glass stainless moldings have a rib on the back of the molding that snaps between the body and the molding clips. Apply a thin line of sealant around the edges of the new window. Work from the inside of your car and work out the lip of the weatherstrip in the corner of the quarter glass gently.

Make sure the window is settled evenly and there are no gaps. The quarter panel will be attached to the door with clips. Nathan takes you through the correct way to install your glass back into your classic or vintage car quarter vent framesThis same process applies to the win. Taking some time today to replace a window that my mother broke on this car after she had locked herself out.

Each rear quarter window glass is sealed into a channel which protects the front and lower edges and supports the glass in body opening. Remove the 4 bolts holding the quarter window regulator in place and remove the regulator. Position the rear quarter window glass to the flange and press the retaining tabs into the flange to engage. Whatever you choose to call them they are an often-unnoticed piece of glass that has an important function to play in the safety and security of the vehicle and for enabling all-round visibility for the driver.

For additional information refer to Section 501-05. Install the C-pillar trim panels. Using three to four pieces of masking tape tape the edges of the window to the car frame and hold the glass in place. Position the rear quarter window glass to the flange and press the retaining tabs into the flange to engage.

INSTALL QUARTER WINDOW GLASS a Using a sponge apply the primer on the contact surface of moulding. Install the rear quarter window glass. Theres a square arm at the top of the cover that fits into a matching slot and two small tabs that snap into the hole for the quarter glass retention nut. Step 4 Set the new window into the groove within the window opening.

Steele Rubber Products President Matt Agosta and Scott Goodwin from Goodwin Restorations remove and replace the back window glass weatherstripping on 67 C. The front lower corner of glass and channel assembly is pivoted on a bolt in an adjustable hinge mounted on the rear quarter inner panel. Slowly place the window into the frame and press it firmly along the edges. Make sure the molding rib snaps between the body and clip and not the clip and glass.

Quarter glass also known as a quarter lite or in older vehicles a valence window is a side window. 20 mm 60 mm. Youre going to need a 14 10 mm deep well socket and a short extension in order to access the nuts holding the quarter glass window hinge in place. The part number on this quarter glass is FQ22690 GTY.

Install the up pe r molding first making sure the molding is cente red in the body opening. Start at the top and work towards the corners cutting to the given maximum depths. Check the rear quarter window glass installation for air or water leaks through the urethane seal. Install the rear quarter window glass.

If you re searching for How To Install Rear Quarter Glass Window you've arrived at the ideal location. We have 15 images about how to install rear quarter glass window including images, photos, photographs, backgrounds, and much more. In such page, we additionally have variety of images available. Such as png, jpg, animated gifs, pic art, symbol, blackandwhite, transparent, etc