Mustang How To Install Rear Upper Back Window Glass Molding

There are several options for clips depending on the year of your Ford Mustang and if the clips are for the windshield or the back window.

Mustang how to install rear upper back window glass molding. Steele Rubber Products President Matt Agosta and Scott Goodwin from Goodwin Restorations remove and replace the back window glass weatherstripping on 67 C. Thats why lots of sealer is needed around the fastbacks rear window especially around the outside between the rubber and body. Mustang Door Glass Run Weatherstrip Pair 1965-1966 Installation Instructions. I looked in the Search this Forum here another mustang forum and of course Google using all combinations of.

Rear Upper Back Window Glass Molding is a direct fit for the following. Close your trunk and youre all done. Any tips on installing the rear window trim on a 6970 Mach 1. The rear glass stainless moldings have a rib on the back of the molding that snaps between the body and the molding clips.

Classic Industries offers a wide selection of Ford Mustang parts including Ford Mustang interior parts and soft trim Ford Mustang exterior sheet metal Ford Mustang moldings Ford Mustang emblems Ford Mustang weatherstrip and unique accessories to nearly every nut and bolt needed for installation. Mustang 1 inch Rear Lowering Block Kit 1965-1966 Installation Instructions. Window Molding Clip Front or Rear Coupe 1964 12 - 1965 - Pony Enterprises Window Molding Clip Kit Front and Rear Coupe 1966 - Pony Enterprises Price. The closed-cell foam is placed on the rear window ledge.

1994-2004 Ford Mustang-Designed To Replace The Upper Most Moulding On The Rear Glass Window Please Refer To Compatibility Above Below For Proper Fitment If VIN Is Supplied Before Ordering We Will Confirm Fitment. I dont want to put out the expense or labor to replace the glass so Ill clean and inspect all of the glass to determine the. This molding closes the gap between the body and rear glass to keep water from leaking in to your Mustang. Mustang Blue Instrument Panel Bulb Lenses 1967-1970 Installation Instructions.

What ever money could be saved by doing the installation yourself will be instantly transformed into a very expensive lesson if you crack the glass. The Mustang window molding is held in place with molding retainer clips. Work the molding onto the glass until you reach the other end. Carefully pull off the old factory piece.

If I had clear glass I could purchase new assemblies that come complete. This set of window molding is a direct-fit replacement for your ponys factory original. Also note - the reproduction rear glass weatherstrip is thicker and even stock trim doesnt want to set down on it. 71-73 Back Glass Install.

I didnt install my glass myself but the installer had a similar problem with the SD window molding and actually cracked the front glass trying to put it in. Molding installation follows the same protocol. This Genuine Ford Rear Upper Window Glass Molding Trim is designed to be a direct fit replacement for all 1994 to 2004 Mustang Coupes including the V6 GT Bullitt Mach 1 and SVT Cobra models. Make sure the molding rib snaps between the body and clip and not the clip and glass.

Install the up pe r molding first making sure the molding is cente red in the body opening. There are little pegs on the body surrounding the glass the middle channel int he clip snaps on the peg with the side shown in pic 1 facing the glassyou. 1994-2004 Ford Mustang Designed To Replace The Upper Most Molding On The Rear Glass Window. Glass Inspection and Restoration.

Pop your trunk to gain access to your rear lower glass molding. Reinstallation is easy install the clips the gently snap the molding onto the clips that are already installed on the body. He didnt have any problems that I know of after that. 1965 Mustang uses the same clip for both the front and rear window Part.

I told him about the Carpenter brand rubber. With a firm soft. The rear window must be removed in order to install this molding. Order this Set of 6 Rear Window Moldings for your 1967-68 Mustang Fastback from CJ Pony Parts.

Be careful - they dont warrant the stuff if you ding it. Obviously Im doing something wrong just as with the initial attempt at the window installation. Rear Upper Back Window Glass Moulding Direct Factory Replacement For. But kept coming up dry.

Align one side of the molding and then start pushing the molding over the edge of the glass. It features OEM-style beautiful chrome-plating quality construction. 1996 Mustang Cobra Convertible Procharged423 RWHP 1969 Fastback 351C TKO 600 T-lock. This is the black rubber moulding that surrounds the top of the rear window in your 1994-2004 Mustang V6 GT or Cobra.

Measure the window opening and unroll the foam to create an overlap for the window opening then fold the. Purchasing new Mustang glass can be expensive and in my case if I buy new tinted glass I would have to reuse the existing stainless trim and window frames. 1969 1970 6970 Mustang Fastback Rear Glass Window Removal Replacement Installation etc.

If you are looking for Mustang How To Install Rear Upper Back Window Glass Molding you've reached the right place. We ve got 15 images about mustang how to install rear upper back window glass molding including images, pictures, photos, backgrounds, and more. In these page, we additionally provide number of graphics available. Such as png, jpg, animated gifs, pic art, logo, blackandwhite, transparent, etc